Logo

B0064 Engine Trouble Code

B0064 Engine

When you check engine light came on code B0064 the reason should be . However your vehicle's manufacturer may have a different definition for the B0064 OBD-II Diagnostic Body (B) Trouble Code. So you should chech it on our car models.

Theoretically you can drive a few more days or even months with a broken MAF sensor in your car. You will notice a decrease in gas mileage/km and over time the car will at the end start stalling a lot from engine side. At a shop, the replacement cost is between $300-$450 depending on the car, but that's usually the cost of parts because the labor is relatively simple.

B0064 Code Meaning :

B
OBD-II Diagnostic Body (B) Trouble Code For Engine
0
Intake Valve Control Solenoid Circuit Low
0
Injector Circuit Malfunction - Cylinders
6
Injection Pump Fuel Metering Control 'A' High (Cam/Rotor/Injector)
4
Clutch Position Sensor Circuit Malfunction

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

B0064 OBD-II Diagnostic Body (B) Trouble Code Description

B0064 engine trouble code is about Clutch Position Sensor Circuit Malfunction. Injector Circuit Malfunction - Cylinders and Injection Pump Fuel Metering Control 'A' High (Cam/Rotor/Injector) causes most of code B0064.

Reason For B0064 Code

The reason of B0064 OBD-II Engine Trouble Code is Injector Circuit Malfunction - Cylinders.

B0064 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is over-retarded, the engine trouble light will be illluminated and the code will be set.

How To Repair B0064 Code

Before starting let's see B0064 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access B0064 code stored in the ECU.
  • Technicians will note B0064 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

A faulty ECM could result in the vehicle to be dealing with a reduction in fuel efficiency, power, and acceleration. A vehicle that fails to start or struggles to start is another main symptom or a defective or failed ECM. If the ECM fails completely, the vehicle will remain with no engine control management, and will not be starting or running as a result.

B0064 code is stored again, the mechanic will perform a visual inspection of the pressure control solenoid and related systems. If any circuits or connections are damaged or loose, they will resolve these issues and move on to retest the system.

Sometimes B0064 code comes with B006400 code.

Diagnosis Of Engine Error OBD Code B0064

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a B0064 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the B0064 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.